Pay in installments of $29.70 with
,
and
Shipping Estimate
USA
- USA
- CAN
- USA
- CAN
Ships within 48 hours · Estimated delivery Jul 25 - Jul 30
Promo Codes Available:
For Your Every Summer RSVP, with Code: SUMMER15
Description
LC1D258D7Main Range TeSys Product name TeSys D Product or component type Contactor Device short name LC1D Contactor application Resistive load Utilisation category AC 1 Poles description 4P Power pole contact composition 2 NO + 2 NC [Ue] rated operational voltage Power circuit: <= 690 V AC 25 400 Hz Power circuit: <= 300 V DC [Ie] rated operational current 40 A (at <60 C) at <= 440 V AC AC 1 for power circuit Control circuit type AC at 50 60 Hz [Uc] control
Main
| Range | TeSys |
| Product name | TeSys D |
| Product or component type | Contactor |
| Device short name | LC1D |
| Contactor application | Resistive load |
| Utilisation category | AC-1 |
| Poles description | 4P |
| Power pole contact composition | 2 NO + 2 NC |
| [Ue] rated operational voltage | Power circuit: <= 690 V AC 25...400 Hz Power circuit: <= 300 V DC |
| [Ie] rated operational current | 40 A (at <60 °C) at <= 440 V AC AC-1 for power circuit |
| Control circuit type | AC at 50/60 Hz |
| [Uc] control circuit voltage | 42 V AC 50/60 Hz |
| Auxiliary contact composition | 1 NO + 1 NC |
| [Uimp] rated impulse withstand voltage | 6 kV conforming to IEC 60947 |
| Overvoltage category | III |
| [Ith] conventional free air thermal current | 10 A (at 60 °C) for signalling circuit 40 A (at 60 °C) for power circuit |
| Irms rated making capacity | 140 A AC for signalling circuit conforming to IEC 60947-5-1 250 A DC for signalling circuit conforming to IEC 60947-5-1 450 A at 440 V for power circuit conforming to IEC 60947 |
| Rated breaking capacity | 450 A at 440 V for power circuit conforming to IEC 60947 |
| [Icw] rated short-time withstand current | 240 A 40 °C - 10 s for power circuit 380 A 40 °C - 1 s for power circuit 50 A 40 °C - 10 min for power circuit 120 A 40 °C - 1 min for power circuit 100 A - 1 s for signalling circuit 120 A - 500 ms for signalling circuit 140 A - 100 ms for signalling circuit |
| Associated fuse rating | 10 A gG for signalling circuit conforming to IEC 60947-5-1 63 A gG at <= 690 V coordination type 1 for power circuit 40 A gG at <= 690 V coordination type 2 for power circuit |
| Average impedance | 2 mOhm - Ith 40 A 50 Hz for power circuit |
| [Ui] rated insulation voltage | Power circuit: 690 V conforming to IEC 60947-4-1 Power circuit: 600 V CSA certified Power circuit: 600 V UL certified Signalling circuit: 690 V conforming to IEC 60947-1 Signalling circuit: 600 V CSA certified Signalling circuit: 600 V UL certified |
| Electrical durability | 1.4 Mcycles 40 A AC-1 at Ue <= 440 V |
| Power dissipation per pole | 3.2 W AC-1 |
| Safety cover | With |
| Mounting support | Rail Plate |
| Standards | CSA C22.2 No 14 EN 60947-4-1 EN 60947-5-1 IEC 60947-4-1 IEC 60947-5-1 UL 508 |
| Product certifications | RINA GL DNV GOST LROS (Lloyds register of shipping) CCC BV UL CSA |
| Connections - terminals | Control circuit: screw clamp terminals 1 cable(s) 1…4 mm²flexible without cable end Control circuit: screw clamp terminals 2 cable(s) 1…4 mm²flexible without cable end Control circuit: screw clamp terminals 1 cable(s) 1…4 mm²flexible with cable end Control circuit: screw clamp terminals 2 cable(s) 1…2.5 mm²flexible with cable end Control circuit: screw clamp terminals 1 cable(s) 1…4 mm²solid without cable end Control circuit: screw clamp terminals 2 cable(s) 1…4 mm²solid without cable end Power circuit: connector 1 cable(s) 2.5…10 mm²flexible without cable end Power circuit: connector 2 cable(s) 2.5…10 mm²flexible without cable end Power circuit: connector 1 cable(s) 2.5…10 mm²flexible with cable end Power circuit: connector 2 cable(s) 2.5…10 mm²flexible with cable end Power circuit: connector 1 cable(s) 2.5…16 mm²solid without cable end Power circuit: connector 2 cable(s) 2.5…16 mm²solid without cable end |
| Tightening torque | Control circuit: 1.7 N.m - on screw clamp terminals - with screwdriver flat Ø 6 mm Control circuit: 1.7 N.m - on screw clamp terminals - with screwdriver Philips No 2 Power circuit: 1.8 N.m - on connector - with screwdriver flat Ø 6 mm Power circuit: 1.8 N.m - on connector - with screwdriver Philips No 2 |
| Operating time | 12...22 ms closing 4...19 ms opening |
| Safety reliability level | B10d = 1369863 cycles contactor with nominal load conforming to EN/ISO 13849-1 B10d = 20000000 cycles contactor with mechanical load conforming to EN/ISO 13849-1 |
| Mechanical durability | 15 Mcycles |
| Maximum operating rate | 3600 cyc/h 60 °C |
Complementary
| Coil technology | Without built-in suppressor module |
| Control circuit voltage limits | Drop-out: 0.3...0.6 Uc AC 50/60 Hz (at 60 °C) Operational: 0.8...1.1 Uc AC 50 Hz (at 60 °C) Operational: 0.85...1.1 Uc AC 60 Hz (at 60 °C) |
| Inrush power in VA | 70 VA 60 Hz cos phi 0.75 (at 20 °C) 70 VA 50 Hz cos phi 0.75 (at 20 °C) |
| Hold-in power consumption in VA | 7.5 VA 60 Hz cos phi 0.3 (at 20 °C) 7 VA 50 Hz cos phi 0.3 (at 20 °C) |
| Heat dissipation | 2…3 W at 50/60 Hz |
| Auxiliary contacts type | Type mechanically linked 1 NO + 1 NC conforming to IEC 60947-5-1 Type mirror contact 1 NC conforming to IEC 60947-4-1 |
| Signalling circuit frequency | 25...400 Hz |
| Minimum switching current | 5 mA for signalling circuit |
| Minimum switching voltage | 17 V for signalling circuit |
| Non-overlap time | 1.5 ms on de-energisation between NC and NO contact 1.5 ms on energisation between NC and NO contact |
| Insulation resistance | > 10 MOhm for signalling circuit |
Environment
| IP degree of protection | IP20 front face conforming to IEC 60529 |
| Protective treatment | TH conforming to IEC 60068-2-30 |
| Pollution degree | 3 |
| Ambient air temperature for operation | -5…60 °C |
| Ambient air temperature for storage | -60…80 °C |
| Permissible ambient air temperature around the device | -40…70 °C at Uc |
| Operating altitude | 3000 m without |
| Fire resistance | 850 °C conforming to IEC 60695-2-1 |
| Flame retardance | V1 conforming to UL 94 |
| Mechanical robustness | Vibrations contactor open: 2 Gn, 5...300 Hz Vibrations contactor closed: 4 Gn, 5...300 Hz Shocks contactor closed: 15 Gn for 11 ms Shocks contactor open: 8 Gn for 11 ms |
| Height | 105 mm |
| Width | 45 mm |
| Depth | 99 mm |
| Net weight | 0.425 kg |
Offer Sustainability
| Sustainable offer status | Green Premium product |
| REACh Regulation | REACh Declaration |
| EU RoHS Directive | Compliant EU RoHS Declaration |
| Toxic heavy metal free | Yes |
| Mercury free | Yes |
| RoHS exemption information | Yes |
| China RoHS Regulation | China RoHS declaration |
| Environmental Disclosure | Product Environmental Profile |
| Circularity Profile | End of Life Information |
| WEEE | The product must be disposed on European Union markets following specific waste collection and never end up in rubbish bins |
Contractual warranty
| Warranty | 18 months |
Shipping Notes
- Free Standard Shipping on $100+ Orders to the USA.
- Except Preorder products are shipped in 48 hours.
- Delivery to the USA:
- Standard Shipping : 3-10 business days
- If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
- We offer a 30-day return/exchange service after receiving.
- Final sale items are not eligible for returns or exchanges.
- To process your return/exchange, please contact us at [email protected]
- Please click here for more details>>> Return & Exchange Policy
4.2 ★★★★★
Based on 27 reviews
Sort
Product Reviews
★★★★★ 1
Did not work.
Size: 96158T-2PCS
I went to double check that I can read but it says 35hp-275hp and it sure didn’t work on my 200ho mercury so I do not recommend. If you’re on a time crunch don’t push your luck buy OEM like I am doing right after this review.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 13, 2026
★★★★★ 5
Great Banana Plugs
Size: 6 Pairs / 12 pcs
I recently purchased these FosPower banana plugs to tidy up my speaker wiring, and they’ve been a significant improvement over bare wire ends. Installation is straightforward: strip the wire, loosen the two tiny set screws, slide the wire in, tighten everything down, and then screw the barrel back on. Once assembled, the connection feels secure and tight, making it much easier to swap gear around and reducing the risk of stray strands causing a short.
The standout feature of this design is the dual set-screw clamp. It firmly grips the speaker wire without relying on the outer collar to “crush” it in place. I’m using 12-gauge wire, and it holds well for my setup.
Initially, the plugs may fit snugly in some binding posts. Once seated, there’s no wobble, but it might take a bit of extra push the first time.
The set screws are small, so a bit of precision is needed. Use a small flathead screwdriver and don’t over-tighten them.
Overall, these plugs feel well-made, look clean once installed, and fulfill their purpose as banana plugs: making speaker connections quick, neat, and reliable.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 27, 2026
★★★★★ 5
Great Banana Plugs!
Size: 6 Pairs / 12 pcs
These FosPower banana plugs work very well. I have used dozens of these great FosPower banana plugs over the years, and they definitely work as advertised. When comparing apples to apples (or bananas in this case....lol), all Banana plugs work virtually the same way, and these banana plugs are no different. Strip speaker wire, unscrew banana plug cover, loosen speaker wire retaining screw(s), insert speaker wire, tighten speaker wire retaining screw(s), screw on banana plug cover, and wallah, a secure/conductive speaker/amplifier wire connector is created. Albeit, some banana plugs require the speaker wire to be splayed over a hollow post, and then they are held down by a screw-on retainer/cover. However, I much prefer these FosPower dual retaining screw type of banana plugs for their speaker wire holding ability.
I always use high quality 14 gauge OFC speaker wire with these FosPower banana plugs, and they work perfectly together. I have used these FosPower banana plugs with many different speaker and amplifier brands over the years, including Klipsch, Pioneer, Polk, Denon, Dayton Audio, and Fosi with no problems at all. They just work, and work well. I have never had a FosPower banana plug break, release the speaker wire or short out, in all of the years that I have used them.
Yes, these FosPower banana plugs do fit rather tightly into the connectors, at first, on a lot of speaker and amplifier brands/models. However, after the initial "squeeze" the banana plugs will lossen up, and become easier to install and remove. However, they still retain their great holding ability even after the initial squeeze. In order to overcome this initial "tightness," I usually just stick the FosPower banana plugs into a connector of an old portable amplifier, before assembling them, in order to squeeze them before inserting them into their final speaker or amplifier destinations. This is especially useful when working in tight places, where there is not much room to work in order to push the FosPower banana plugs into their tight connections firmly.
Overall, I highly recommend these FosPower banana plugs. I am currently using them all over the house and shop for home theater and music listening (and testing projects). Just be aware of the tight fit in some speakers and amplifiers. Also, the 2 very tiny speaker wire retaining screws can be a challenge sometimes. Just use a good standard blade jewelers screwdriver, and be careful not to remove the retaining screws all of the way or over-tighten them. Once these things are mastered, using these FosPower banana plugs becomes second nature. Have fun!
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on August 28, 2024
★★★★★ 5
Great Product
Size: 6 Pairs / 12 pcs
These banana plugs have worked perfectly, no matter what gauge I have run in them, they work great. Easy assembly and great quality.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 8, 2026
★★★★★ 4
The most legit banana plugs I could find on Amazon
Size: 6 Pairs / 12 pcs, Size: 6 Pairs / 12 pcs
NEW PREFACE:: I am kind of glad I first bought the horribly magnetic, horribly made and GOLD PAINTED Sewell crimp on plugs (some reviewers say that Sewell are better and easier to use than the FosPower, which is true in design, but in quality of materials FosPower beats them hands down!!) ... Changing from those to these FosPower plugs plus the Monoprice 90° plugs, I am flabbergasted at the difference they make in sound quality. I have heard people say that they can hear the difference and even as an audiophile I was skeptical..... but my skepticism has been completely erased by what I am hearing with my own ears. I waited a few days to make sure I wasn’t just tripping before updating this review 🤣....but it has become clear to me how much a difference plugs made from the right materials actually make!!! I am 100% serious that the bass coming out of my Polk Signature Series tower speakers has at least doubled at the same volume. I can also now turn the volume up Way past my max volume before, without any distortion and much more clarity and less harsh highs. Everything just sounds warmer in general now which is amazing!!!! This is dangerous info for me... because now I’m thinking about making some really nice custom wires to see how much of a difference that makes 🙄🙄🤣 OK onto the review of the actual plugs here~~
These seem like decent connectors. I can’t tell if they are brass or copper, but they only have a slight hint of a magnetic property when testing them with a very powerful magnet. I was easily able to fit x2 - 14ga wires into it for bi-wiring purposes, including screwing on the collar. (As seen in my example pic) The gold plating on the tips seems legit and not painted like some of the plugs from Sewell... I have tested and tried quite a few plugs from Amazon and most seem to be crap. These however hold up better than most! These and the Monoprice 90° banana plugs with the black and red rubber sleeves. The latter are gold plated copper and have zero magnetic properties. (if you need 90° banana plugs)
UPDATE: still the best plugs I have found, but upon full install found two issues. One is a defect where a set of the plug threads for the barrel cover body weren’t cut right. The body’s do not tighten and stay loose because of that. Obvious issue for vibration with metal on metal...
The other issue is that even though these say they can fit different gauge wires, they seem to be geared more towards 12 or 10 gauge. I am using semi solid strand 14 gauge and find that unless I fold the wire over to make it double thick, the bolts use up all the thread and seem to become kind of loose inside the body. They won’t fully seat and keep spinning no matter how much you tighten. They seem to stay secure still but I just wonder about longevity over time with vibrations. So I just doubled up the wire and they seated fine! Not the worst issue in the world, but just kind of a pain since you have to strip the wire longer than you normally would so you can fold it over.
ANOTHER UPDATE: I had to remove these plugs from the wire to connect them to a crappy spring terminal amp while my better amp was in the shop. The issue I wrote about with the set screws "bottoming out" on smaller gauge wire became a more pronounced issue! I could not unscrew the set screws anymore and just had to cut the wires... So that means I will need to purchase more of these to replace the ones I cannot get wire back into. Not the best design, but still one of the best plugs I have found on Amazon.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on March 26, 2021