Total Micro Projector Lamp for the IN110xa and IN110xv Series

Upgrade your projector performance with the Total Micro Projector Lamp, engineered specifically for the IN110xa and IN110xv Series. This high-quality replacement lamp helps you maintain sharp image brightness, precise color fidelity, and dependable operation across presentations, classrooms, and home theaters. Built to supersede the original lamp, it delivers consistent results, easier maintenance, and improved longevity, so you can focus on your content rather than equipment concerns. Whether you’re delivering a critical business presentation, teaching a dynamic lesson, or enjoying immersive viewing, this lamp is designed to maximize your projector’s potential with reliable performance and enhanced efficiency.

• Compatibility and replacement performance: Specifically engineered to replace the original lamp in IN110xa and IN110xv projectors, ensuring a seamless fit, reliable ignition, and stable brightness from the moment you power on. This replacement lamp is designed to deliver the same or better performance as the OEM, so you can trust it for presentations, lectures, and entertainment.
• Long life in multiple modes: Normal mode offers up to 5000 hours of consistent brightness for everyday usage, while Low Power mode extends life to approximately 6000 hours, reducing the frequency of replacements. In Eco Blanking mode, you can achieve up to around 15000 hours, helping you save on maintenance costs during long sessions or setups with standby usage. These ranges help you tailor consumption to your environment without sacrificing image quality.
• Bright, stable output with reliable color: Designed to sustain bright, even illumination and faithful color reproduction across modes. The Total Micro Lamp maintains brightness consistency as it ages, helping ensure your documents, graphics, and videos remain clear and legible even during extended use. This stability is especially important for business and education scenarios where color accuracy matters.
• Easy installation and safe handling: The lamp is intended for straightforward replacement with minimal downtime. Follow simple steps to swap the old lamp for the Total Micro unit, and let the projector’s light output reset and stabilize. Safe handling practices—such as avoiding direct contact with the glass and allowing the lamp to cool before replacement—help protect the lamp’s life and performance while reducing the risk of damage to your projector.
• Energy efficiency and cost savings: By offering a high-quality replacement with optimized life in Low Power and Eco Blanking modes, this lamp supports lower energy consumption and extended usage between replacements. This translates to a lower total cost of ownership over the life of your IN110xa or IN110xv projector, while maintaining strong brightness and dependable operation for daily use.

Technical Details of Total Micro Projector Lamp for the IN110xa and IN110xv Series

• Model: Total Micro Projector Lamp
• Compatibility: IN110xa and IN110xv Series
• Normal Life: Approximately 5000 hours
• Low Power Mode Life: Approximately 6000 hours
• Eco Blanking Life: Up to approximately 15000 hours
• Engineered to supersede OEM: Yes, designed to replace the original lamp in compatible projectors
• Installation type: Replacement projector lamp module suitable for IN110xa and IN110xv

How to Install Total Micro Projector Lamp

• Power off the projector, unplug it from the power source, and allow the device to cool completely before handling any internal components.
• Open the projector’s service/access panel according to the manufacturer’s instructions, and locate the existing lamp module. Do not touch the lamp glass with bare hands; handle the lamp by its housing to prevent oils from your skin transferring to the surface.
• Carefully disconnect the old lamp and remove it from the housing. Inspect the socket and surrounding area for any signs of damage or debris, and remove any dust if needed.
• Insert the Total Micro Projector Lamp into the socket until it clicks securely into place. Ensure the lamp is seated evenly and the connector is firmly attached before reassembling the projector.
• Reattach the lamp cover and close the service panel. If your projector requires a lamp timer reset, follow the manufacturer’s instructions to reset the lamp counter to ensure accurate usage tracking.
• Plug in the projector, power it on, and allow a few minutes for the lamp to warm up and stabilize. Run a brief test image to verify brightness uniformity and color accuracy across different areas of the screen.

Frequently Asked Questions

• Q: Is this lamp compatible with the IN110xa and IN110xv projectors? A: Yes. The Total Micro Projector Lamp is engineered to replace the original lamp in the IN110xa and IN110xv series, providing reliable performance and compatibility with those models.
• Q: What is the expected lifespan in different modes? A: In Normal mode, you can expect about 5000 hours of operation. In Low Power mode, the life extends to about 6000 hours. Eco Blanking mode can reach up to roughly 15000 hours, depending on usage and environmental conditions.
• Q: Do I need to reset the lamp timer after installation? A: In many projectors, yes. Some units require a lamp timer reset after replacement to ensure accurate usage measurements. Consult your projector’s manual for the exact procedure applicable to your model.
• Q: How should I handle and store the lamp? A: Handle the lamp by its housing, avoid touching the glass, and store in its protective packaging if not installing immediately. Keep it in a cool, dry place away from direct sunlight and conductive materials.
• Q: Will this lamp affect image quality or brightness? A: The Total Micro Projector Lamp is designed to deliver consistent brightness and color across its rated life. Proper installation and environmental conditions help maintain optimal image quality and avoid color shifts or brightness drop‑offs.